Student preparing for a multiple-choice competitive exam

Pakistan's MCQ Practice Library for Competitive Exams

mcqpk.com helps students and job candidates practise multiple-choice questions by subject, then build a free test to check what they have learned.

Questions are reviewed over time, but syllabuses and factual answers can change. Always confirm important information with the relevant official source.

Start a practice testHow we review MCQs

Prepare for your exam

FPSCFederal recruitment MCQ preparationPPSCPunjab recruitment test preparationKPPSCKP screening and ability testsNTSNAT and GAT practice guidanceCSS MPTCSS 2027 preliminary preparation

Recently added practice questions

1221. Which of the following must be followed by the flow of a fluid (real or ideal)? (I) Newtons law of viscosity. (II) Newtons second law of motion. (III) The continuity equation. (IV) Velocity of boundary layer must be zero relative to boundary. (V) Fluid cannot penetrate a boundary?
comments icon0

A. I, II, III

B. II, III, V

C. I, II, V

D. II, IV, V

1222. Which of the following muscles elevates the mandible ?
comments icon0
A. Temporalis

B. Ganinus

C. Lateral pterygoid

D. Buccinator

1223. Which of the following muscle helps in depressing the mandible ___________?
comments icon0
A. Lateral pterygoid

B. Temporalis

C. Medial pterygoid

D. Massetor

1224. Which of the following muscle divides the sub- mandibular gland into a superficial and deep part ?
comments icon0

A. Sternohyoid

B. Genioglossus

C. Mylohyoid

D. Digastric

1225. Which of the following movement (s) is / are involved in the opening of the mouth?
comments icon0

A. Only translation

B. Translation followed by hinge

C. Hinge followed by translation

D. Only hinge ( rotation )

1226. Which of the following Motorway is called Sukkur to Hyderabad Motorway in Pakistan.
comments icon0

A. M-8

B. M-6

C. M-10

D. M-3

1227. Which of the following motors is usually preferred for kiln drives ?
comments icon0

A. Three phase shunt wound com-mutator motor

B. Any of the above

C. Slip ring induction motor

D. Cascade controlled A.C. motor

1228. Which of the following motors is used in a situation where load increases with speed ?
comments icon0

A. Hysteresis motor

B. Induction motor

C. Three-phase series motor

D. Schrage motor

1229. Which of the following motors is used for unity power factor ?
comments icon0

A. Reluctance motor

B. Hysteresis motor

C. Schrage motor

D. Universal motor

1230. Which of the following motors is preferred when smooth and precise speed control over a wide range is desired ?
comments icon0

A. Wound rotor induction motor

B. Squirrel cage induction motor

C. D.C. motor

D. Synchronous motor

1231. Which of the following motors is preferred for tape-recorders ?
comments icon0
A. Hysteresis motor

B. Two value capacitor motor

C. Universal motor

D. Shaded pole motor

1232. Which of the following motors has two separate windings on the motor ?
comments icon0

A. None of the above

B. Repulsion start induction run motor

C. Repulsion motor

D. Repulsion induction motor
1233. Which of the following motors can be used for unity power factor ?
comments icon0

A. Shaded pole motor

B. Schrage motor

C. Capacitor run motor

D. Hysteresis motor

1234. Which of the following motors are pre-ferred for overhead travelling cranes ?
comments icon0

A. Continuous duty motors

B. None of the above

C. Short time rated motors

D. Slow speed motors

1235. Which of the following motor will give the highest starting torque ?
comments icon0

A. D.C. shunt motor

B. Universal motor

C. Schrage motor

D. Repulsion start and induction run motor

1236. Which of the following motor will give relatively high starting torque ___________?
comments icon0

A. Split phase motor

B. Capacitor start motor

C. Capacitor run motor

D. Shaded pole motor

1237. Which of the following moment are performed by a non- working condyle ?
comments icon0

A. Down wards Back wards and medial

B. Down wards forwards and lateral

C. Straightward

D. Down wards forwards and medial

1238. Which of the following mineral dressing operations is termed as comminution?
comments icon0

A. Spiralling

B. Panning

C. Tabling

D. None of these
1239. Which of the following methods of theodolite traversing is suitable for locating the details which are far away from transit stations ?
comments icon0

A. measuring angle and distance from one transit station

B. measuring angles to the point from at least two stations

C. measuring distance from two points on traverse line

D. measuring angle at one station and distance from other

1240. Which of the following methods of structural analysis is a force method ?
comments icon0

A. none of the above

B. column analogy method

C. moment distribution method

D. slope deflection method

How to use MCQPK

  1. Choose a subject from the navigation or subject directory.
  2. Work through the questions and compare each option with the marked answer.
  3. Use the online quiz to practise a mixed or subject-specific set.
  4. Report a doubtful answer so it can be reviewed and corrected.

MCQPK is an independent study resource. It is not affiliated with FPSC, PPSC, KPPSC, NTS or any other testing body.