Student preparing for a multiple-choice competitive exam

Pakistan's MCQ Practice Library for Competitive Exams

mcqpk.com helps students and job candidates practise multiple-choice questions by subject, then build a free test to check what they have learned.

Questions are reviewed over time, but syllabuses and factual answers can change. Always confirm important information with the relevant official source.

Start a practice testHow we review MCQs

Prepare for your exam

FPSCFederal recruitment MCQ preparationPPSCPunjab recruitment test preparationKPPSCKP screening and ability testsNTSNAT and GAT practice guidanceCSS MPTCSS 2027 preliminary preparation

Recently added practice questions

3721. The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is________________?
comments icon0

A. 8-Jan

B. 1/16

C. 12-Jan

D. 10-Jan

3722. The ratio of the diameter of a circular section and the side of a square section hydraulically equivalent, is____________________?
comments icon0

A. 1.065

B. 1.075

C. 1.095

D. 1.085

3723. The ratio of the area of openings in one screen (Taylor series) to that of the openings in the next smaller screen is_________________?
comments icon0

A. 1

B. None of these

C. 1.5

D. ?2

3724. The ratio of the actual mesh dimension of Taylor series to that of the next smaller screen is_______________?
comments icon0

A. 1.5

B. ?3

C. 2

D. ?2
3725. The ratio of maximum to average velocity in case of streamline flow between parallel plates is______________________?
comments icon0

A. 2.5

B. 1.5

C. 1

D. 2

3726. The ratio of maximum shear stress to average shear stress of a circular beam, is________________?
comments icon0

A. 4-Mar

B. 3-Feb

C. 2-Mar

D. 4/3
3727. The ratio of maximum and average shear stresses on a rectangular section, is________________?
comments icon0
A. 1.5

B. 1

C. 1.25

D. 2.5

3728. The ratio of lateral strain to linear strain is termed as the___________________?
comments icon0

A. Bulk modulus

B. Modulus of elasticity

C. Poissons ratio

D. Shear modulus

3729. The ratio of kinematic viscosity to thermal diffusivity is called the _______________ number?
comments icon0

A. Peclet

B. Nusselt

C. Stanton

D. Prandtl
3730. The ratio of isentropic work to eulers work is known as _____________________?
comments icon0

A. pressure ratio

B. Eulers efficiency

C. isentropic efficiency

D. compressor efficiency

E. pressure coefficient
3731. The ratio of intensity of magnetisation to the magnetisation force is known as_____________?
comments icon0

A. flux density

B. susceptibility

C. none of the above

D. relative permeability

3732. The ratio of inertial forces to gravity forces is called the ______________ number?
comments icon0

A. Euler

B. Weber

C. Froude

D. Mach

3733. The ratio of inertial forces to gravity forces is called the ______________ number?
comments icon0

A. Euler

B. Froude

C. Weber

D. Mach

3734. The ratio of endurance limit in shear to the endurance limit in flexure is__________________________?
comments icon0

A. 0.5

B. 0.6

C. 0.55

D. 0.4

E. 0.33

3735. The ratio of actual cultivated area to a total farm area over the year is called __________________?
comments icon0

A. Cost benefit ratio

B. Cropping pattern

C. Cropping intensity

D. Cropping system

3736. The ratio of active power to apparent power is known as factor__________?
comments icon0
A. power

B. demand

C. load

D. form

3737. The ratio of a new price to the base year price is called the___________?
comments icon0

A. Price increase

B. Price absolute

C. Price decrease

D. Price relative
3738. the ratio between the rate of change of discharge of the out let to the rate of change of discharge of the distributary is called ______________________?
comments icon0
A. flexibility

B. Flow abili

C. Proportionally

D. Sensitivity

3739. The rather humid climate in no way _____ from the beauty of the place.
comments icon0

A. attracts

B. detracts

C. protracts

D. subtracts

3740. The rated loads of lifting cranes, as percentage of tipping load at specified radius, for crawler-mounted, and pneumatic tyremounted machines would be respectively_________________?
comments icon0

A. 90 and 80

B. 85 and 75

C. 80 and 90

D. 75 and 83

How to use MCQPK

  1. Choose a subject from the navigation or subject directory.
  2. Work through the questions and compare each option with the marked answer.
  3. Use the online quiz to practise a mixed or subject-specific set.
  4. Report a doubtful answer so it can be reviewed and corrected.

MCQPK is an independent study resource. It is not affiliated with FPSC, PPSC, KPPSC, NTS or any other testing body.