civil engineering Mcqs
4101. Pandrol clips cannot be used with__________________?
comments icon0

A. steel trough sleepers

B. concrete sleepers

C. CST-9 sleepers

D. wooden sleepers

4102. Stretcher bar is provided________________?
comments icon0

A. to permit lateral movement of the tongue rail

B. to ensure exact gauge at the toe of the switch as well as the nose of crossing

C. to maintain the two tongue rails at the exact distance

D. to prevent any vertical movement between the wing rail and nose of crossing

4103. A train is hauled by 2-8-2 locomotive with 22.5 tonnes and on each driving axle. Assuming the coefficient of rail-wheel friction to be 0.25, what would be the hauling capacity of the locomotive?
comments icon0
A. 22.5 tonnes

B. 45.0 tonnes

C. 15.0 tonnes

D. 90.0 tonnes

4104. The purpose of providing fillet in a rail section is to_________________?
comments icon0

A. increase the vertical stiffness

B. increase the lateral strength

C. avoid the stress concentration

D. reduce the wear

4105. avoidance of block instruments 4. higher operating cost Of these statements_____________________?
comments icon0

A. 3 and 4 are correct

B. 2 and 3 are correct

C. I and 2 are correct

D. 1 and 4 are correct

4106. The type of spike used for fixing chairs of bull headed rails to wooden sleepers is_________________?
comments icon0

A. elastic spike

B. dog spike

C. round spike

D. rail screw

4107. Sleeper density in India is normally kept as___________________?
comments icon0

A. MtoM+2

B. M

C. M + 5toM+10

D. M + 2 to M + 7
4108. The type of bearing plate used in all joints and on curves to give better bearing area to the rails is___________________?
comments icon0
A. mild steel canted bearing plate

B. cast iron anti creep bearing plate

C. none of the above

D. flat mild steel bearing plate

4109. The distance through which the tongue rail moves laterally at the toe of the switch for movement of trains is called_________________?
comments icon0

A. flangeway clearance

B. heel divergence

C. throw of the switch

D. none of the above

4110. In a scissors cross-over, the crossings provided are_________________?
comments icon0
A. 2 obtuse angle crossings

B. 6 acute angle crossings</strong>

C. ) 4 acute angle crossings

D. 4 obtuse angle crossings

E. correct answer is ?

4111. In a shunting signal if the red band is inclined at 45 it indicates_________________?
comments icon0

A. none of the above

B. stop

C. proceed cautiously

D. proceed
4112. Which of the following mechanical devices is used to ensure that route cannot be changed while the train is on the point even after putting back the signal ?
comments icon0

A. detectors

B. stretcher bar

C. iock bar

D. point lock

4113. The following tests are conducted for rails _________________?
comments icon0

A. compulsory tests are?

B. falling weight test

C. tensile test

D. ) hammer test</strong>

4114. If A is the angle formed by two gauge faces, the crossing number will be____________________?
comments icon0

A. tan A

B. cot A

C. Arad

D. sec A

4115. Lead of crossing is the distance from the__________________?
comments icon0
A. heel of the switch to the theoretical nose of the crossing

B. heel of the switch to the toe of the switch

C. toe of the switch to the actual nose of crossing

D. toe of the switch to the theoretical nose of crossing

4116. Ordinary rails are made of_______________?
comments icon0

A. wrought iron

B. mild steel

C. cast iron

D. high carbon steel
4117. For a Broad Gauge route with M+7 sleeper density, number of sleepers per rail length is________________?
comments icon0

A. 21

B. 20

C. 19

D. 18

4118. Maximum value of throw of switch for Broad Gauge track is__________________?
comments icon0
A. 115 mm

B. 89 mm

C. 95 mm

D. 100 mm

4119. Staggered joints are generally provided__________________?
comments icon0

A. none of the above

B. when two different rail sections are required to be joined

C. on curves

D. on straight track

4120. Standard size of wooden sleeper for Broad Gauge track is____________________?
comments icon0

A. 225x23x13 cm

B. 250x26x12 cm

C. 275x25x13cm

D. 180x20x11.5 cm

4121. For the purpose of track maintenance, the number of turn out equivalent to one track km are__________________?
comments icon0

A. 1

B. 2

C. 10

D. 5

4122. The reception signal is__________________?
comments icon0

A. advanced starter

B. home signal

C. correct answer is?

D. outer signal

E. ) starter

4123. Number of cotters used in CST-9 sleepers is__________________?
comments icon0
A. 4

B. 3

C. 2

D. 5

4124. Dog spikes are used for fixing rail to the__________________?
comments icon0

A. steel trough sleepers

B. CST-9 sleepers

C. concrete sleepers

D. wooden sleepers
4125. Largest dimension of a rail is its________________?
comments icon0
A. height

B. any of the above

C. foot width

D. head width

4126. 60 R rails are mostly used in__________________?
comments icon0

A. Broad Gauge

B. Narrow Gauge

C. none of the above

D. Metre Gauge
4127. At points and crossings, the total number of sleepers for 1 in 12 turnouts in Broad Gauge is______________?
comments icon0

A. 62

B. 51

C. 78

D. 70
4128. Minimum composite sleeper index pres-cried on Indian Railways for a track sleeper is_______________?
comments icon0

A. 1352

B. 1455

C. 783

D. 552

4129. Normally the limiting value of cant is________________?
comments icon0

A. G/8

B. G/12

C. G/10

D. G/15

4130. The main function of a fish plate is________________?
comments icon0

A. to allow rail to expand and contract freely

B. to join the two rails together

C. to join rails with the sleeper

D. none of the above

4131. A Broad Gauge branch line takes off as a contrary flexure from a main line If the superelevation required for branch line is 10 mm and cant deficiency is 75 mm, the superelevation to be actually provided on the branch line will be__________________?
comments icon0

A. 85 mm

B. 64 mm

C. 65 mm

D. 10 mm

4132. Switch angle depends on______________?
comments icon0

A. length of tongue rail

B. heel divergence

C. correct answer is?

D. ) flangeway clearance

E. throw of switch</strong>

4133. The correct relation between curve lead (CL), switch lead (SL) and lead of crossing (L) is given by__________________?
comments icon0

A. SL = L + CL

B. CL = L SL

C. L = (CL+SL)/2

D. L =CL-SL
4134. The maximum degree of curvature for Meter Gauge is limited to_________________?
comments icon0

A. 10

B. 16

C. 30

D. 40

4135. Switch angle is the angle between___________________?
comments icon0

A. the outer face of the stock rail and the gauge face of the tongue rail

B. the outer face of the stock rail and tongue rail

C. the gauge face of the stock rail and outer face of the tongue rail

D. the gauge face of the stock rail and tongue rail
4136. The desirable rate of change of cant deficiency in case of Metre Gauge is_______________?
comments icon0

A. 55 mm/sec

B. 65 mm/sec

C. 35 mm/sec

D. 20 mm/sec

4137. A treadle bar is used for_____________________?
comments icon0
A. interlocking points and signal

B. setting points and crossings

C. setting marshalling yard signals

D. track maintenance

4138. Which of the following devices is used to transfer the wagons or locomotives to and from parallel tracks without any necessity of shunting ?
comments icon0

A. scotch block

B. turntable

C. triangle

D. traverser
4139. Vertical curves are provided where algebraic difference between grades is equal to or_________________?
comments icon0
A. more than 4mm/m

B. more than 2 mm/m

C. less than 2 mm/m

D. less than 4 mm/m

4140. Creep is the_______________?
comments icon0

A. vertical movement of rail

B. lateral movement of rail

C. longitudinal movement of rail

D. difference in level of two rails

4141. The slipping of driving wheels of locomotives on the rail surface causes_______________?
comments icon0

A. corrugation of rails

B. wheel burns

C. scabbing of rails

D. hogging of rails

4142. Which of the following factors govern the choice of the gauge ?
comments icon0
A. volume and nature of traffic

B. speed of train

C. correct answer is ?

D. ) physical features of the country</strong>

4143. Wear of rails is maximum in weight of___________________?
comments icon0
A. sharp curve

B. tangent track

C. coastal area

D. tunnels

4144. When the rail ends rest on a joint sleeper, the joint is termed as_________________?
comments icon0

A. suspended rail joint

B. bridge joint

C. base joint

D. supported rail joint
4145. Consider the following statements about concrete sleepers_________________?
comments icon0

A. They render transportation easy.

B. They have good scrap value.

C. They maintain the gauge quite satisfactorily.Of these statements </strong>

D. They improve the track modulus.
4146. Due to battering action of wheels over the end of the rails, the rails get bent down and are deflected at ends. These rails are called_________________?
comments icon0

A. corrugated rails

B. hogged rails

C. roaring rails

D. buckled rails

4147. The standard length of rail for Broad Gauge and Meter Gauge are respectively __________________?
comments icon0

A. 13 m and 13 m

B. 12 m and 13 m

C. 13 m and 12 m

D. 12 m and 12 m

4148. Lead of crossing is the distance from the_________________?
comments icon0
A. heel of the switch to the theoretical nose of the crossing

B. toe of the switch to the theoretical nose of crossing

C. toe of the switch to the actual nose of crossing

D. heel of the switch to the toe of the switch

4149. 52 kg rails are mostly used in__________________?
comments icon0
A. Broad Gauge

B. Meter Gauge

C. Narrow Gauge

D. both (A) and (B)

4150. The cross-sectional area of 52 kg flat footed rail is_________________?
comments icon0

A. 7825 mm2

B. 7235 mm2

C. 6615 mm2

D. 6155 mm2