civil engineering MCQs – Page 77

Practise multiple-choice questions from civil engineering for competitive examinations and subject revision. Review each marked answer and report any item that may be outdated or unclear.

civil engineering Mcqs
3801. Select the correct range of density index,ID ________________?
comments icon0

A. 0 < lD < 1

B. 0 < ID < 1

C. ID>0

D. lD>0

3802. At liquid limit, all soils possess________________?
comments icon0

A. different shear strengths of small magnitude

B. different shear strengths of large magnitude

C. same shear strength of large magnitude

D. same shear strength of small magnitude
3803. In a deposit of normally consolidated clay_________________?
comments icon0

A. effective stress, water content and undrained strength decrease with depth

B. effective stress and undrained strength increase with depth but water content decreases with depth

C. effective stress and water content increase with depth but undrained strength decreases with depth

D. effective stress increases with depth but water content of soil and un-drained strength decrease with depth

3804. The degree of kinematic indeterminacy of a pin-jointed space frame is_____________?
comments icon0

A. re j is number of joints and r is reaction components

B. 2j-r

C. j-3r

D. j-2r

E. 3j-r
3805. In column analogy method, the area of an analogous column for a fixed beam of span L and flexural rigidity El is taken as__________________?
comments icon0

A. L/3EI

B. L/2EI

C. L/4EI

D. L/EI
3806. Which of the following methods of structural analysis is a force method ?
comments icon0

A. none of the above

B. column analogy method

C. moment distribution method

D. slope deflection method

3807. The deflection at any point of a perfect frame can be obtained by applying a unit load at the joint in_________________?
comments icon0

A. inclined direction

B. the direction in which the deflection is required

C. vertical direction

D. horizontal direction

3808. Select the correct statement?
comments icon0

A. Flexibility matrix is a square symmetrical matrix

B. Stiffness matrix is a square symmetrical matrix

C. both A. and B.

D. none of the above

3809. When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that___________________?
comments icon0

A. the head of the load reaches the section

B. the tail of the load reaches the section

C. the load position should be such that the section divides it equally on both sides

D. the load position should be such that the section divides the load in the same ratio as it divides the
3810. Castiglianos first theorem is applicable_______________?
comments icon0

A. for statically determinate structures only

B. only when principle of superposition is valid

C. when the system behaves elastically

D. none of the above

3811. The degree of static indeterminacy of a rigid-jointed space frame is_________________?
comments icon0

A. 3m + r 3j

B. m + r 2j

C. 6m + r 6j

D. m + r 3j

E. re m, r and j have their usual meanings

3812. For a single point load W moving on a symmetrical three hinged parabolic arch of span L, the maximum sagging moment occurs at a distance x from ends. The value of x is__________________?
comments icon0

A. 0.25 L

B. 0.234 L

C. 0.5 L

D. 0.211 L
3813. If in a pin-jointed plane frame (m + r) > 2j, then the frame is________________?
comments icon0

A. none of the above

B. unstable

C. stable and statically determinate

D. re m is number of members, r is reaction components and j is number of joints

E. stable and statically indeterminate
3814. Bending moment at any section in a conjugate beam gives in the actual beam_________________?
comments icon0
A. deflection

B. slope

C. bending moment

D. curvature

3815. The width of the analogous column in the method of column analogy is _________________?
comments icon0

A. 2/EI

B. 1/EI

C. 1/4 EI

D. 1/2 EI

3816. The deformation of a spring produced by a unit load is called _________________?
comments icon0
A. flexibility

B. unit strain

C. influence coefficient

D. stiffness

3817. When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when________________?
comments icon0

A. none of the above

B. the wheel load under consideration is midway between the centre of span and the centre of gravity of the load system

C. the centre of gravity of the load system is midway between the centre of span and wheel load under consi-deration

D. the centre of span is midway between the centre of gravity of the load system and the wheel load under consideration
3818. When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies_______________?
comments icon0

A. more than the left half span

B. whole of left half span

C. whole span

D. less than the left half span

3819. The number of independent equations to be satisfied for static equilibrium in a space structure is___________________?
comments icon0
A. 6

B. 2

C. 3

D. 4

3820. While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of__________________?
comments icon0

A. infinite length

B. none of the above

C. zero moment of inertia

D. zero length
3821. In moment distribution method, the sum of distribution factors of all the members meeting at any joint is always__________________?
comments icon0
A. 1

B. less than 1

C. greater than 1

D. zero

3822. The carryover factor in a prismatic member whose far end is fixed is___________________?
comments icon0

A. 4-Mar

B. 1

C. 1/2

D. 0

3823. In the slope deflection equations, the deformations are considered to be caused by________________?
comments icon0

A. correct answer is

B. shear force

C. ) axial force</strong>

D. bending moment
3824. A load W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is___________________?
comments icon0

A. 0.20 Wl

B. 0.24 Wl

C. 0.25 Wl

D. 0.16 Wl

3825. The number of independent displacement components at each joint of a rigid-jointed space frame is_______________?
comments icon0
A. 6

B. 1

C. 3

D. 2

3826. When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would_______________?
comments icon0

A. change from tension to compression

B. always be compression

C. always be tension

D. change from compression to tension
3827. If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is_______________?
comments icon0

A. none of the above

B. stable and statically determinate

C. stable and statically indeterminate

D. unstable
3828. If there are m unknown member forces, r unknown reaction components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame is given by__________________?
comments icon0

A. m + r + 2j

B. m + r 2j

C. m + r 3j

D. m r + 2j

3829. The principle of virtual work can be applied to elastic system by considering the virtual work of_________________?
comments icon0

A. none of the above

B. internal forces only

C. internal as well as external forces

D. external forces only

3830. The degree of static indeterminacy up to which column analogy method can be used is__________________?
comments icon0

A. 2

B. 3

C. unrestricted

D. 4

3831. Principle of superposition is applicable when___________________?
comments icon0
A. deflections are linear functions of applied forces

B. the action of applied forces will be affected by small deformations of the structure

C. material obeys Hookes law

D. none of the above

3832. For a two-hinged arch, if one of the supports settles down vertically, then the horizontal thrust______________?
comments icon0

A. is decreased

B. becomes zero

C. remains unchanged

D. is increased

3833. A single rolling load of 8 kN rolls along a girder of 15 m span. The absolute maximum bending moment will be________________?
comments icon0

A. 8 kN.m

B. 15 kN.m

C. 30 kN.m

D. 60 kN.m

3834. For a symmetrical two hinged parabolic arch, if one of the supports settles horizontally, then the horizontal thrust__________________?
comments icon0

A. is increased

B. becomes zero

C. remains unchanged

D. is decreased
3835. Effects of shear force and axial force on plastic moment capacity of a structure are respectively to_________________?
comments icon0
A. decrease and decrease

B. increase and increase

C. decrease and increase

D. increase and decrease

3836. A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
comments icon0
A. 5 mm

B. 0.5 mm

C. 0.05 mm

D. 0.005mm

3837. Muller Breslaus principle for obtaining influence lines is applicable to___________________?
comments icon0

A. statically determinate beams and frames

B. any statically indeterminate structure</strong>

C. ) statically indeterminate structures, the material of which is elastic and follows Hookes law

D. trusses
3838. Which of the following is not the displacement method ?
comments icon0
A. Column analogy method

B. Equilibrium method

C. Kanis method

D. Moment distribution method

3839. A rigid-jointed plane frame is stable and statically determinate if_______________?
comments icon0

A. re m is number of members, r is reaction components and j is number of joints

B. (3m + r) = 3j

C. (m + r) = 3j

D. (m + 3r) = 3j

E. (m + r) = 2j

3840. A pin-jointed plane frame is unstable if________________?
comments icon0

A. m + r = 2j

B. (m + r)

C. (m + r)>2j

D. none of the above

3841. Number of unknown internal forces in each member of a rigid jointed plane frame is_____________?
comments icon0

A. 1

B. 3

C. 2

D. 6

3842. Which of the following methods of structural analysis is a displacement method ?
comments icon0

A. none of the above

B. moment distribution method

C. three moment equation

D. column analogy method

3843. The Castiglianos second theorem can be used to compute deflections________________?
comments icon0

A. in statically determinate structures only

B. at the point under the load only

C. for beams and frames only

D. for any type of structure
3844. Degree of kinematic indeterminacy of a pin-jointed plane frame is given by______________?
comments icon0
A. 2j r

B. j 2r

C. 2j + r

D. 3j r

3845. The number of independent equations to be satisfied for static equilibrium of a plane structure is__________________?
comments icon0

A. 1

B. 6

C. 3

D. 2

3846. The three moments equation is applicable only when___________________?
comments icon0

A. the spans are equal

B. there is no discontinuity such as hinges within the span

C. there is no settlement of supports

D. the beam is prismatic

3847. Sinking of an intermediate support of a continuous beam________________?
comments icon0

A. sider the following statements

3848. The maximum bending moment due to a train of wheel loads on a simply supported girder_________________?
comments icon0

A. always occurs at centre of span

B. always occurs under a wheel load

C. none of the above

D. never occurs under a wheel load

3849. To generate the j the column of the flexibility matrix________________?
comments icon0

A. a unit displacement is applied at co-ordinate j and the forces are calculated at all coordinates

B. a unit displacement is applied at co-ordinate j and the displacements are calculated at all co-ordinates

C. a unit force is applied at coordinate j and the forces are calculated at all coordinates

D. a unit force is applied at coordinate j and the displacements are calculated at all coordinates
3850. Independent displacement components at each joint of a rigid-jointed plane frame are_________________?
comments icon0

A. one linear movement and two rotations

B. three linear movements

C. three rotations

D. two linear movements and one rotation