electrical engineering MCQs – Page 342

Practise multiple-choice questions from electrical engineering for competitive examinations and subject revision. Review each marked answer and report any item that may be outdated or unclear.

electrical engineering Mcqs

1. economics of power generation 2. analog electronics 3. solid state switching circuits 4. parallel circuits 5. switchgear and protection 6. op amp circuits 7. transistor audio power amplifiers 8. electrostatics 9. heating and welding 10. multi stage transistor amplifiers 11. passive filters 12. network theorems 13. regulated d c power supply 14. a c fundamentals circuits and circuit theory 15. electromagnetic induction 16. power electronics 17. magnetism and electromagnetism 18. transformers 19. modulation and demodulation 20. d c generators 21. semiconductor theory 22. single phase induction motors 23. semiconductor diode 24. hybrid parameters 25. digital electronics 26. oscillators 27. earthing or grounding 28. single stage transistor amplifiers 29. d c motors 30. transistor biasing 31. amplifiers with negative feedback 32. basic electrical 33. electronic instruments 34. synchronous motors 35. field effect transistors fet 36. magnetic circuit 37. control systems 38. industrial drives 39. power generation 40. series parallel circuits 41. transistor tuned amplifiers 42. electrical engineering materials 43. rectifiers and converters 44. integrated circuits 45. scr silicon controlled rectifiers 46. cables 47. polyphase induction motors 48. measurement and instrumentation 49. transistors 50. electrical machine design 51. electrolysis and storage of batteries 52. electric traction 53. transmission and distribution

6821. If a 3-phase supply is given to the stator and rotor is short circuited rotor will move___________?
0

A. in the opposite direction as the direction of the rotating field

B. in any direction depending upon phase squence of supply

C. in the same direction as the direction of the field

6822. In a three-phase induction motor_______________?
0

A. iron losses in motor will be negligible as compared to that in rotor

B. iron losses in stator will be more than that in rotor

C. iron losses in stator will be negligible as compared to that in rotor

D. iron losses in stator will be less than that in rotor

6823. In squirrel cage induction motors, the rotor slots are usually given slight skew in order to__________?
0

A. reduce magnetic hum

B. reduce eddy currents

C. reduce accumulation of dirt and dust

D. reduce windage losses

6824. As load on an induction motor goes on increasing______________?
0

A. its power factor remains constant

B. its power factor goes on decreasing

C. its power factor goes on increasing even after full load

D. its power factor goes on increasing up to full load and then it falls again

6825. In case of 3-phase induction motors, plugging means__________?
0

A. pulling the motor directly on line without a starter

B. interchanging two supply phases for quick stopping

C. locking of rotor due to harmonics

D. starting the motor on load which is more than the rated load

6826. What will happen if the relative speed between the rotating flux of stator and rotor of the induction motor is zero ?
0

A. The torque produced will be very large

B. The slip of the motor will be 5%

C. The rotor will run at very high speed

D. The rotor will not run

6827. The torque of a rotor in an induction motor under running condition is maximum__________?
0

A. at the unit value of slip

B. at the value of the slip which makes the rotor reactance half of the rotor

C. at the value of the slip which makes rotor reactance per phase equal to the resistance per phase

D. at the zero value of slip

6828. In case the air gap in an induction motor is increased?
0

A. the magnetising current of the rotor will decrease

B. the power factor will decrease

C. speed of motor will increase

D. the windage losses will increase

6829. Lubricant used for ball bearing is usually___________?
0

A. graphite

B. mineral oil

C. grease

D. molasses

6830. The injected e.m.f. in the rotor of induction motor must have__________?
0

A. zero frequency

B. the same phase as the rotor e.m.f.

C. high value for the satisfactory speed control

D. the same frequency as the slip frequency

6831. In three-phase squirrel-cage induction motors____________?
0

A. rotor conductors are connected to insulation

B. rotor conductors are kept open

C. rotor conductors are short-circuited through end rings

D. rotor conductor ends are short-circuited through slip rings

6832. Slip ring motor is recommended where____________?
0

A. frequent starting, stopping and reversing is required

B. high starting torque is needed

C. speed control is required

D. all above features are required

6833. Which type of bearing is provided in small induction motors to support the rotor shaft ?
0

A. Ball bearings

B. Cast iron bearings

C. None of the above

D. Bush bearings

6834. Less maintenance troubles are experienced in case of___________?
0

A. slip ring induction motor

B. squirrel cage induction motor

C. both A. and (b)

D. none of the above

6835. In the circle diagram for induction motor, the diameter of the circle represents____________?
0

A. rotor current

B. running torque

C. line voltage

D. slip

6836. In medium sized induction motors, the slip is generally around___________?
0

A. 0.04%

B. 4%

C. 0.40%

D. 14%

6837. An induction motor is identical to_________?
0

A. synchronous motor

B. D.C. compound motor

C. D.C. series motor

D. asynchronous motor

6838. An induction motor with 1000 r.p.m. speed will have____________?
0

A. 2 poles

B. 6 poles

C. 8 poles

D. 4 poles

6839. The power factor of an induction motor under no-load conditions will be closer to_____________?
0

A. 0.2 lagging

B. 0.5 leading

C. unity

D. 0.2 leading

6840. Star-delta starting of motors is not possible in case of____________?
0

A. single phase motors

B. high speed motors

C. low horse power motors

D. variable speed motors

Previous Next

Showing 6821 to 6840 of 7381 mcqs