machine design MCQs – Page 7

Practise focused machine design questions with marked answers for exam preparation and subject revision.

machine design Mcqs
121. Spring index is___________________?
comments icon0

A. load required to produce unit deflection

B. ratio of coil diameter to wire diameter

C. nothing

D. indication of quality of spring

E. its capability of storing energy

122. Which is correct statement ?
comments icon0

A. a member made of steel will generally be more rigid than a member of equal load-carrying ability made of cast iron

B. a member made of cast iron will generally be. more rigid than a member of equal load carrying ability made of steel

C. both will be equally rigid

D. which one is rigid will depend on several other factors

E. none of the above

123. If a load W is applied instantaneously on a bar; then the stress induced in bar will___________________?
comments icon0

A. increase with increase in y

B. depend on other considerations

C. none of the above

D. be independent of ratio of mass of load W to mass of bar (y)

E. decrease with decrease in y

124. In standard taper roller bearings, the angle of taper of outer raceway is___________________?
comments icon0

A. 8

B. 5

C. 15

D. 40.

E. 25
125. In testing a material for endurance strength, it is subjected to_______________________?
comments icon0

A. static as well as dynamic load

B. static load

C. completely reversed load

D. impact load

E. dynamic load

126. The maximum stress due to stress concentration in a bar having circular transverse hole, as compared to its static stress without hole will be_________________?
comments icon0

A. same in both cases

B. 2 times more

C. 3 times more

D. 4 times more

E. unpredictable

127. The shear plane in case of bolts should_________________?
comments icon0

A. be across threaded portion of shank

B. never be across the threaded portion

C. none of the above

D. be normal to threaded portion of shank

E. be parallel to axis of bolt

128. In composite or reverse laid ropes___________________?
comments icon0

A. none of the above

B. wires in two adjacent strands are twisted in opposite direction

C. direction of twist of wires and strands are same

D. wires are not twisted

E. direction of twist of wires in strands is opposite to the direction of twist of strands

129. Guests theory of failure is applicable for following type of materials_________________?
comments icon0

A. tough

B. elastic

C. ductile

D. plastic

E. brittle

130. When a bolt is subjected to shock loading, the resilience of the bolt should be considered in order to prevent breakage at_______________?
comments icon0

A. in the middle

B. anywhere in the bolt

C. at the thread

D. shank

E. head

131. In order to obtain bolt of uniform strength____________________?
comments icon0

A. increase its length

B. drill an axial hole through head up to threaded portion so that shank area is equal to root area of thread

C. all of the above

D. increase shank diameter

E. tighten die bolt properly

132. The designation M 33 x 2 of a bolt means___________________?
comments icon0
A. metric threads of 33 mm outside diameter and 2 mm pitch

B. bolt of 33 mm nominal diameter having 2 threads per cm

C. metric threads with cross-section of 33 mm

D. metric threads of 33 nos in 2 cm.

E. none of the above

133. Which of the following is a permanent fastening ?
comments icon0

A. screws

B. cotters

C. keys

D. rivets

E. bolts

134. If the tearing efficiency of a riveted joint is 75%, then the ratio of diameter of rivet to the pitch is equal to___________________?
comments icon0

A. 0.75

B. 0.25

C. 0.5

D. 0.2

E. 0.6

135. Rivets are generally specified by_______________?
comments icon0

A. all of the above

B. thickness of plates to be riveted

C. length of rivet

D. nominal diameter

E. diameter of head

136. Jam nut is a locking device in which _____________________?
comments icon0
A. one smaller nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming

B. a slot is cut partly in middle of nut and then slot reduced by tightening a screw

C. through slots are made at top and a cotter-pin is passed through these and a hole in the bolt, and cotter spitted and bent in reverse direction at other end

D. a hard fiber or nylon cotter is recessed in the nut and becomes threaded as the nut is screwed on the bolt causing a tight grip

E. none of the above

137. A key capable of tilting in a recess milled out in a shaft is known as______________________?
comments icon0

A. feather key

B. wood-ruff key

C. hollow saddle key

D. flat saddle key

E. gib head key

138. Buttress threads are usually found on____________________?
comments icon0

A. screw jack

B. feed mechanisms

C. spindles of bench vices

D. screw cutting lathes

E. railway carriage couplings